Test & Measurement

Keysight DSOX4145A

The lab owns a number of 1.5 GHz, 4-analog-channel oscilloscopes, with nearly all software features enables, including an internal signal generator. AWG is possible up to 200 kHz, while 20 MHz sinewave or squarewave generation is also possible.

Keysight N5247B PNA-X

Contact Dr. Nagle for training BEFORE ANY USE.

Specializing in characterizing active devices like amplifiers, mixers, and frequency converters, this hardware includes dual internal signal sources, a signal combiner, S-parameter and noise receivers, pulse modulators and generators, internal bias tees, low phase noise capability and a set of switches and RF access points. Covers a frequency range from 10 MHz to 67 GHz.

The only VNA you’ll ever need. Unless you want to move it. Then you’ll need a friend.

The instrument is supplied with 1.85 mm connectors, cables, a comb generator e-Cal units for power and S parameters. To serve as many RLE researchers as possible, 1.85 mm to 3.5 mm connector adapters and cables are available (normally attached to the instrument), as well as a 3.5 mm eCal kit. Passive calibration kits are also available for both 1.85 mm and 3.5 mm.

HP8510C (Keysight)

Thanks to the generosity of Professor Jeff Lang, the lab has a permanent loan of an HP8510C vector network analyzer with a 20 GHz source and an S-parameter test set capable to 40 GHz.

Click Here

Instek GPP-4323 Four-Channel Programmable DC Power Supply

  • Supports Setting Value, Measurement Value and Output Waveform Display
  • Load Function (CC, CV, CR Mode)
  • Setting Resolution: 1mV / 0.1mA; Read Back Resolution: 0.1mV / 0.1mA
  • Low Ripple Noise: ≦350uVrms/ ≦2mArms
  • Transient Response Time: ≦50uS
  • Utilizing Hardware to Realize Over Voltage Protection / Over Current Protection / Over Temperature Protection
  • Delay Function / Output Monitoring Function / Output Recorder Function
  • Sequential Output Function and Built-in 8 Template Waveforms
  • The Output Recorder Function Records The Output Voltage & Current Parameters with A Minimum Recording Interval of 1 Second.

Keysight DSOX1204G

The lab owns a number of 200 MHz bandwidth, 4-analog-channel oscilloscopes, which include an internal signal generator.

Keysight N6705C - DC Power Analyzer

  • Mainframe only – modules sold separately
  • See below for modules that the lab owns.
  • Combines one to four DC power supplies or Electronic loads, DMM, oscilloscope, arbitrary waveform generator, and data logger in one integrated instrument
  • Up to 600W total DC output power
  • Mix and match DC source power levels and measurement performance levels to optimize your investment
  • Gain insights into the DUT’s power consumption in minutes without writing a single line of code

Keysight N6781A - Two Quadrant SMU Module for Battery Drain Analysis

  • Used in the N6705C mainframe
  • Two quadrant source/measure unit for battery drain analysis
  • Voltage: up to 20 V
  • Current: up to ±3 A
  • Power: 20 W
  • For use with N6700 low-profile modular power systems or N6705 DC power analyzers

Keysight N6762A - Precision DC Power Module

  • Used in the N6705C mainframe
  • For use with N6700 low-profile modular power systems or N6705 DC power analyzers
  • Size: one slot
  • Voltage: 50V
  • Current: 3A
  • Power: 100W

Keysight N6733B - DC Power Module

  • Used in the N6705C mainframe
  • For use with N6700 low-profile modular power systems or N6705 DC power analyzers
  • Size: one slot
  • Voltage: 20V
  • Current: 2.5A
  • Power: 50W

Keysight N6756A - High Performance, Autoranging DC Power Module

  • Used in the N6705C mainframe
  • Size: two slots
  • Voltage: 60V
  • Current: 17A
  • Power: 500W

AmScope 3.5X-180X

Simul-Focal Stereo Zoom Microscope on Boom Stand with an LED Light and 16MP USB3 Camera connected to a networked computer.